Access Point Cisco WAP4410N-BR T Access Point Wireless-N with PoE

Specifications 

Standards 
Draft IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af
(Power over Ethernet), 802.1x (security authentication), 802.11i security WPA/WPA2, WMM
Ports 
Ethernet, Power
Buttons 
Reset
Cabling type 
Unshielded twisted pair (UTP) Category 5e or higher
LEDs 
Power, Ethernet, Wireless, PoE
Operating system 
Linux
Setup/Configuration 
Web user interface 
Built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
Management 
Simple Network Management Protocol (SNMP) version 
SNMP version 1, 2c
Event logging 
Event logging
Email logging
Remote syslog
Web firmware upgrade 
Firmware upgradeable through web browser
Diagnostics. 
Flash, RAM, LAN, WLAN
Dynamic Host Configuration Protocol (DHCP) 
DHCP client
HTTP Redirect 
Redirects initial user access to an external web server to display company logo or network usage policy
IPv6 host 
Support for management and control of access point over IPv6
Supports RFC2460 (IPv6 protocol) and RFC4294 (IPv6 node requirements)
Network Capabilities
Multiple BSSID 
Supports up to 4 BSSIDs, allowing the creation of multiple virtual access points
VLANs 
Supports 802.1q - up to 4 VLANs
SSID to VLAN mapping 
Supports mapping of SSIDs to VLANs to securely separate workgroups across wireless and wired domains
Spanning Tree 
Supports 802.1d Spanning Tree Protocol to prevent loops when using wireless distribution system (WDS) links as redundant links in a distribution system
Operating modes Access 
point mode, point-to-point bridge mode, point-to-multipoint bridge mode, repeater mode, wireless client mode
Load balancing 
Allows bandwidth control with user-defined CPU usage ratios
Auto-channel selection 
On boot-up, the access point selects the least congested channel
802.11d regulatory domain 
Enables the access point to provide radio channel settings for client devices, facilitating easy client access as they move across regulatory domains
Security 
WEP/WPA/WPA2 
Wired Equivalent Privacy (WEP) 64-bit/128-bit, WPA-Pre-Shared Key (WPA-PSK), WPA2- PSK, WPA-ENT, WPA2-ENT
Access control 
Wireless connection control: MAC-based
SSID broadcast 
SSID broadcast enable/disable
Client isolation 
Supports wireless client isolation between and within SSIDs
802.1X 
Wireless clients can be authenticated through IEEE 802.1X
802.1X supplicant 
Supports 802.1X supplicant on the Ethernet port to allow the access point to authenticate itself to the network
RADIUS server 
Up to 2 RADIUS servers can be configured for redundancy purposes
WPS 
Supports WPS, a WI-FI Alliance specification for simple and secure setup of a wireless network
Rogue access point detection 
New access points detected that have not been categorized as known are logged as rogue access points, allowing the administrator to clamp down on unapproved devices in the network
Quality of Service 
QoS 
4 queues
802.1p VLAN priority
WMM wireless priority
Mapping of 802.1p VLAN priority to WMM wireless priority to maintain end-to-end QoS
Wireless 
Spec/modulation 
Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM, 802.11n/OFDM
Channels 
Operating channels: 11 North America, 13 most of Europe (ETSI and Japan)
Internal antennas 
None
External antennas 
3 (omnidirectional)
Transmit power 
Transmit power @ normal temp range for FCC:
802.11b: 16 dBm @ 1TX, 19 dBm @ 2TX, 20.5 dBm @ 3TX
802.11g: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX
802.11n: 17 dBm @ 1TX @ MCS0~5/8~13, 13 dBm @ 1TX @ MCS6/14,
11 dBm @ 1TX @ MCS7/15, 20 dBm @ 2TX@MCS0~5/8~13,
16 dBm @ 2TX @ MCS6/14, 14 dBm @ 2TX @ MCS7/15,
21.5 dBm @ 3TX@MCS0~5/8~13, 17.5 dBm @ 3TX @ MCS6/14,
15.5 dBm @ 3TX @ MCS7/15
Transmit power @ normal temp range for ETSI:
11b/g/n: 13 dBm @ 1TX, 16 dBm @ 2TX, 17.5 dBm @ 3TX
Antenna gain in dBi 
2
Receiver sensitivity 
802.11.n: 300 Mbps at -69dBm
802.11.g: 54 Mbps at -73dBm
802.11.b: 11 Mbps at -88dBm
Environmental 
Dimensions 
6.69 x 6.69 x 1.60 in.
W x H x D 
(170 x 170 x 40.7 mm)
Weight 
0.86 lb (39 kg)
Power 
12V 1A DC input, and IEEE 802.3af compliant PoE
Max power draw: 10.1W
Certification 
FCC, CE, IC
Operating temperature 
32 to 104F (0 to 40C)
Storage temperature 
-4 to 158F (-20 to 70C)
Operating humidity 
10% to 85%, noncondensing
Storage humidity 
5% to 90%, noncondensing
Package Contents 
Cisco WAP4410N Wireless-N Access Point with PoE
User guide on CD-ROM
Ethernet network cable
Power adapter
Product stands
Registration card
Minimum Requirements 
802.11b, 802.11g, 802.11n wireless adapter with TCP/IP protocol installed per PC
Switch/router with PoE support or PoE injector when used with PoE
Web-based configuration: Java-enabled web browser